feat: init repo and scripts and readme

README.md

@@ -0,0 +1,62 @@
+# How to use Huawei 3372s under linux
+
+
+https://www.0xf8.org/2017/01/flashing-a-huawei-e3372h-4g-lte-stick-from-hilink-to-stick-mode/
+
+## How to flash
+
+1. `sudo ./balong-usbdload -p /dev/ttyUSB0 usblsafe-3372h.bin` DO NOT
+   TOUCH the usb key, you should see 3 new tty poping
+2. `sudo ./balong_flash -p /dev/ttyUSB2 Huawei_E3372h-153_21.180.01.00.00_Firmware_general_3Ginfo.ru/E3372h-153_UPDATE_21.180.01.00.00.BIN`
+
+
+* [See the fuck here with linux drivers](https://askubuntu.com/questions/816974/huawei-usb-modem-proper-drivermodule-is-not-loading/818374#818374)
+
+https://wiki.dd-wrt.com/wiki/index.php/Cellular_Phone/USB_Modem_as_WAN_connection
+
+https://openwrt.org/docs/guide-user/network/wan/wwan/ethernetoverusb_ncm
+
+1. Delete old /dev/ttyUSBx can save your life
+1. Doing a `rmmod option` can solve a lot
+
+
+1. You should have `usb-devices`
+
+```
+T:  Bus=01 Lev=01 Prnt=01 Port=06 Cnt=03 Dev#= 68 Spd=480 MxCh= 0
+D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
+P:  Vendor=12d1 ProdID=1506 Rev=01.02
+S:  Manufacturer=HUAWEI_MOBILE
+S:  Product=HUAWEI_MOBILE
+C:  #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=2mA
+I:  If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=option
+I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option
+I:  If#=0x2 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=huawei_cdc_ncm
+I:  If#=0x3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
+I:  If#=0x4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
+```
+
+1. `ip link` must show a device like `wwx00XXXXXXXXX`
+
+1. To enable connection
+1. `socat - /dev/ttyUSB0,crnl`
+1. `ATI` show basic informations
+1. `AT+CPIN=1234` if you have a pin code
+1. `AT+CGDCONT=1,"IP","m2m.tele2.com"` for setup a APN
+1. `AT^NDISDUP=1,1,` to enable APN should show => `^NDISSTAT:1,,,"IPV4"`
+1. Then you enable wwx iface with `ip link set up wwx00XXXXXXXXX`
+1. Then send shcp request `dhclient -v wwx00XXXXXXXXX`
+
+## On DDWRT
+
+1. Usb drivers debug helpful command `cat /sys/kernel/debug/usb/devices`
+1. You need to load kernel module first `insmod cdc-ncm.ko cdc_wdm.ko huawei_cdc_ncm.ko usb_wwan.ko option.ko` TODO finish this
+1. Switch the Huawei in modem mode `usb_modeswitch -v 0x12d1 -p 0x14fe -J`
+1. You should see a change in `lsusb`
+1. You should see `wwan0: register 'huawei_cdc_ncm' at usb-0000:00:0b.1-2, Huawei CDC NCM device, 00:1e` in `dmesg` command output
+1. Enable connection `echo -ne "AT^NDISDUP=1,1,\"sl2sfr\"\r\n" > /dev/ttyUSB0`
+1. `ifconfig wwan0 up` see this documentation here
+1. `udhcpc -i wwan0`
+1. `iptables -t nat -A POSTROUTING -o wwan0 -j MASQUERADE`
+1. `iptables -A FORWARD -i br0 -j ACCEPT`
+1. `iptables -t mangle -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu`

connect-huawei-e3372.sh

@@ -0,0 +1,10 @@
+#!/bin/sh
+
+# Load linux kernel modules
+# For gsm serial console on /dev/ttyUSBx
+modprobe -v option
+# For Huawei CDC NCM ether card
+modprobe -v huawei_cdc_ncm
+usb_modeswitch -v 0x12d1 -p 0x14fe -J
+sleep 2
+echo -ne "AT^NDISDUP=1,1,\"sl2sfr\"\r\n" > /dev/ttyUSB0

refresh-connect-huawei-e3372.sh

@@ -0,0 +1,14 @@
+#!/bin/sh
+if ping -c 4 9.9.9.9;
+then
+  echo "4G seems good"
+else
+  echo -ne "AT^NDISDUP=1,0\r\n" > /dev/ttyUSB0
+  sleep 1
+  echo -ne "AT^NDISDUP=1,1,\"sl2sfr\"\r\n" > /dev/ttyUSB0
+  sleep 1
+  udhcpc -i wwan0
+  iptables -t nat -A POSTROUTING -o wwan0 -j MASQUERADE
+  iptables -A FORWARD -i br0 -j ACCEPT
+  iptables -t mangle -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu
+fi